1990 Jeep Cherokee OilsR.Us - Only the Best!

Component Description: Latches/locks/linkages:doors:latch.

Service Bulletin Summary: Redesigned liftgate latch. ( nhtsa item number - 39539 ).

Component Description: Power train:driveline.

Service Bulletin Summary: New front output seal and oil slinger for transfer case. ( nhtsa item number - 37855 ).

Component Description: Engine and engine cooling:exhaust system:emission control.

Service Bulletin Summary: It has been determined that the 1990 jeep vehicle, equipped with the 2. 5l engine, may be in violation of federal emissions standards. Hydrocarbon, carbon monoxide and oxides of nitrogen levels could be above allowable limits, which were e ( nhtsa item number - 39014 ).

Component Description: Engine and engine cooling:exhaust system:emission control.

Service Bulletin Summary: Recall 558 - failure of the oxygen sensor and catalytic converter may cause a vehicle to be in violation of california emissions standards. To correct this condition, the oxygen sensor and catalytic converter must be replaced with improv ( nhtsa item number - 41032 ).

Component Description: Engine and engine cooling:exhaust system.

Service Bulletin Summary: Unknown ( nhtsa item number - 43047 ).

Component Description: Structure:frame and members.

Service Bulletin Summary: Difficult to clean light colored "chalky" residue from plastic body components that are molded in black. ( nhtsa item number - 51942 ).

Component Description: Engine and engine cooling:cooling system.

Service Bulletin Summary: Various car owner's have expressed interest in using engine coolants made with propylene glycol instead of ethylene glycol. ( nhtsa item number - 52963 ).

Component Description: Engine and engine cooling.

Service Bulletin Summary: Concerns with engine coolant usage. ( nhtsa item number - 6088786 ).

Component Description: Power train:automatic transmission:park/neutral start switch.

Service Bulletin Summary: Subject on customer satisfaction notification #733--brake pedal shift interlock. ( nhtsa item number - 600604 ).

Component Description: Equipment:electrical:radio/tape deck/cd etc. .

Service Bulletin Summary: Information on installation of radio transmitting equipment. ( nhtsa item number - 600862 ).

Component Description: Seats.

Service Bulletin Summary: Information on child seat tether anchors. ( nhtsa item number - 607963 ).

Component Description: Structure:body.

Service Bulletin Summary: Subject on the child seat tether anchors. ( nhtsa item number - 612160 ).

Component Description: Electrical system:wiring.

Service Bulletin Summary: This bulletin provides a revised wire splice procedure and related parts. ( nhtsa item number - 609995 ).

Component Description: Seats.

Service Bulletin Summary: Subject regarding child seat tether anchors. ( nhtsa item number - 610635 ).

Component Description: Seats.

Service Bulletin Summary: Subject regarding child seat tether anchors. ( nhtsa item number - 615688 ).

Component Description: Electrical system.

Service Bulletin Summary: Subject regarding wire splice repairs. ( nhtsa item number - 618049 ).

Component Description: Structure:body.

Service Bulletin Summary: Subject regarding floor pan corrosion. ( nhtsa item number - 633948 ).

Affected Component: Exterior lighting.

Summary: Certain pro-a motors corner lamps, turn signals, and headlights sold as replacement lamps for use on certain passenger vehicles listed above. Some combination lamps that are not equipped with amber side reflectors fail to conform to federal motor vehicle safety standard no. 108, lamps, reflective devices, and associated equipment. .

Conequence: Without the amber reflectors, the vehicle will be poorly illuminated, possibly resulting in a vehicle crash without warning. .

Remedy: Pro-a motors will notify owners and offer to repurchase the lamps. The recall began on april 3, 2006. Owners may contact pro-a motors at 323-838-2988. .

Notes: This recall only pertains to pro-a motors aftermarket lamps and has no relation to any original equipment installed on the listed passenger vehicles. For more information on the lamp model numbers, click on document search and view document titled "lamp model numbers. " customers may contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153).

Affected Component: Exterior lighting.

Summary: Sabersport is recalling 16,270 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. These headlamps fail to conform to the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment. " these lamps do not contain the required amber side reflectors. .

Conequence: Decreased lighting visibility may result in a vehicle crash. .

Remedy: Sabersport will notify owners and offer a full refund for the noncompliant combination lamps. The safety recall began on may 11, 2009. Owners may contact sabersport at 1-909-598-7589. .

Notes: This recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles produced by the vehicle manufacturer. In order to determine if your aftermarket lamp assembly is affected by this noncompliance, please review the list of model numbers provided to us by sabersport. The list can be found under "document search" located at the bottom of your screen. Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153).

Affected Component: Exterior lighting:headlights.

Summary: Dope, inc. Is recalling 42,540 combination corner and bumper lamp assemblies of various part numbers sold for use as aftermarket equipment for various passenger vehicles. These headlamps fail to conform to the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment. " these lamps do not contain the required amber side reflectors. .

Conequence: Decreased lighting visibility may result in a vehicle crash. .

Remedy: Dope, inc. Will notify owners and offer a full refund for the noncompliant combination lamps. The safety recall began on july 28, 2009. Owners may contact dope, inc. At 1-626-272-1798. .

Notes: This recall only pertains to aftermarket replacement equipment and has no relation to any original equipment installed on vehicles produced by the vehicle manufacturer. In order to determine if your aftermarket lamp assembly is affected by this noncompliance, please review the list of model numbers provided to us by dope, inc. The list can be found under "document search" located at the bottom of your screen. Owners may also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153).

Affected Component: Vehicle speed control:cruise control.

Summary: Malfunction of fuel injection system throttle postition sensor could cause intermittent high engine idle speed immediately after starting engine. .

Conequence: High engine idle when car is first placed in gear couldresult in unexpected acceleration. .

Remedy: Replace throttle position sensors with sensors that would send correct signals to the fuel injection system. .

Notes: System: throttle position sensor. Vehicle description: multi-purpose vehicles equipped with 4. 0 l engine andautomatic transmission. .

Affected Component: Service brakes, hydraulic:foundation components:hoses, lines/piping, and fittings.

Summary: Improper insertion/crimping of the hose-to-end fittings of the high pressure hose on the anti-lock brake system can cause detachment of the hose from the abs system, and discharge of hydraulic fluid. .

Conequence: Detachment of the hose from the abs system causes theloss of the abs function and hydraulic brake assist, leaving only manual brakesand decreasing stopping ability, which could result in an accident. Discharge ofhydraulic fluid in the area of the hot exhaust system could result in an enginecompartment fire. .

Remedy: Replace the abs high pressure hose. .

Notes: System: anti-lock brake system; abs high pressure hose attachment to end unit. Vehicle description: multipurpose passenger vehicle. .

Affected Component: Service brakes, hydraulic:foundation components:hoses, lines/piping, and fittings.

Summary: There may be hydraulic fluid contamination from condensation formation that can plug the abs brake booster pump filter; stress corrosion of the master cylinder snap ring has been traced to chlorine leaking from the low pressure hydraulic hose which may cause it to break; front brake hose to tire interference which may cause failure of the brake hose. .

Conequence: Contamination of the hydraulic fluid can causemalfunctioning of the anti-lock brake system; low pressure hose leakage causesloss of brake fluid and also results in corrosion and failure of the mastercylinder snap ring, resulting complete brake failure; failure of the front brakehose due to hose to tire interference will cause failure of one half of thebrake system resulting in a longer stopping distance than expected. .

Remedy: Replace abs low pressure hose; rebuild master brake cylinder; inspect, service interference problems, and replace front brake hose as necessary. .

Notes: System: hydraulic fluid contamination; anti-lock brake system (abs). Vehicle description: multi-purpose vehicles equipped with anti-lock brakesystem. .

Affected Component: Service brakes, hydraulic:antilock/traction control/electronic limited slip.

Summary: Vehicle description: vehicles equipped with antilock brake system (abs). The antilock brake system (abs) hydraulic control unit can experience excessive brake actuator piston seal wear which could cause pump-motor deterioration. .

Conequence: If this occurs, the abs function would be lose and reduced power assist would be experienced during vehicle braking. The instrument panel warning lights will signal system impairment and the base manual brakes will remain functional. .

Remedy: Dealers will test the vehicle's abs and repair as necessary. The warranty on all abs components will be extended to 10 years or 100,000 miles (except for the brake actuator piston assembly and the pump-motor assembly which will have a lifetime coverage). Owners will be reimbursed for previous abs component repair costs. .

Notes: Owner notification began april 24, 1997. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-853-1403. Also contact the national highway traffic safety administration's auto safety hotline at 1-800-424-9393. .

Affected Component: Vehicle speed control:accelerator pedal.

Summary: Vehicle description: multipurpose passenger vehicles equipped with automatic transmissions. This is not a safety recall in accordance with federal regulation 573. However, it is deemed a safety improvement campaign by the agency. Drivers can mistakenly step on the accelerator pedal when they intend to step on the brake pedal. .

Conequence: Pedal misapplication by a driver can cause unintended acceleration. .

Remedy: Dealers will install a shift interlock on the automatic transmission of these vehicles. .

Notes: Note: chrysler has decided to conduct a safety improvement campaign to install a shift interlock on these vehicles. Owners can contact chrysler at 1-800-853-1403. .

Affected Component: Service brakes, hydraulic:foundation components:disc:rotor | service brakes, hydraulic:foundation components:disc:rotor.

Summary: Vehicle description: passenger and multi-purpose vehicles originally sold or currently registered in the states of connecticut, illinois, indiana, maine, maryland, massachusetts, michigan, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, or wisconsin, and the district of columbia. The front disc brake rotors can experience severe corrosion if operated for an extensive period in the "salt belt. " if the rotors are not replaced, the corrosion can eventually compromise the structural integrity of the stamped steel center hub section of the rotor. .

Conequence: The reduced strength can allow the cast iron wear surface to separate from the hub, reducing the brake effectiveness of the vehicle. .

Remedy: Dealers will replace these rotors with rotors that are coated with a corrosion protection. .

Notes: Owner notification began march 9, 1998. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chrysler at 1-800-992-1997. Also contact the national highway traffic safety administration's auto safety hotline at 1-888-dash-2-dot (1-888-327-4236). .